Details for Error code E13/0031

ricardonbrito on 2012-01-25 21:03:16 :

check the mosfet q6f1 if shorted replace it, if you keep the error 0031 u4v1
adp1823 surely the integrated circuit is defective too.

ricardonbrito on 2011-11-06 21:11:20 :

I decided yesterday a 0031, tried to do a reflow, and solder balls melted did
not care, after I made ​​the mistake reball 0031, was the capacitor the
capacitor C4R29 That was short, it is below the gpu, and Other Island was the
gpu.

radddogg on 2011-09-19 23:01:24 :

I got this after reflowing and x-clamping a E74 1022. Tried insulating the
components but still the same. Changed to nylon washer under screw heads and
nylon on board/metal to heatsink but more importantly held GPU heatsink away
from CPU heatsink while tightening screws as they look like they can touch each
other otherwise.

modmanrockingham on 2011-07-28 03:28:59 :

un-bridged U6T1 or U6T2 (point that protect cpu-fuse)

worked for me on my Zephur Jtagged xbox360

modmanrockingham on 2011-07-28 03:27:58 :

I am happy to say the un-bridging of the U6T1 or U6T2 fixed the error on my
zephur jtagged xbox360 :)

-SOCAL- on 2011-07-26 11:15:08 :

hey does anyone know how to replace the ram? i had a external 12v fan on my
falcon and i got this error. i reflowed everything and did the electrical tape
thing and the x clamp and it doesnt work

Cerebralone on 2011-06-22 22:42:38 :

Had e74, did the x-clamp trick on both heat sinks to fix, then got this error. I
did what devinogden did, covered everything under GPU heat sink with electrical
tape, fixed the problem.

xbox-jedi on 2011-05-25 21:44:38 :

We fix dozens of consoles a month,
recently had an old E74 turn into a 0031 here,

so probably bridged solder, etc.

masterfulmatt on 2010-11-22 23:39:50 :

had this today on a previously x-clamp fixed machine, was resistor short under
GPU, redid x-clamp fix and covered resistors with layer of kapton tape to ensure
no more shorts, recommend 1)swapping out dvd cable and test, 2) remove gpu
heatsink and test 3) CPU heatsink and test, then try others above

devinogden on 2010-11-02 01:14:42 :

Resistor short confirmed. Received error after performing x clamp fix.
Investigated board for any signs of the problem and found that the gpu or cpu
heatsink (can't quite remember which one) was making contact with a nearby
resistor. I attempted to loosen the screws attached to the heatsink but made it
overheat quickly. To fix this, I removed the heatsinks completely, applied
electrical tape underneath completely covering under the heatsink except of
course the gpu or cpu chips.

Vinces_xbox_repair on 2010-09-12 18:28:16 :

Can some one tell me where I find info to relpace the ram?

PRiME on 2010-07-26 07:28:56 :

I had this error caused by a bad reflow. I reballed the GPU and error was gone
so it definitely can be linked to a bridged solder joint under the GPU as well.
If you can't do reballing it may make it a bit hard to fix so perhaps use
HIGH grade high quality flux to repair it?

BabyStalin on 2010-07-16 02:55:05 :

Where can you buy a new dvd power cord and also where can you buy new RAM bricks
and how do you install them

NickdogV on 2010-06-09 05:39:43 :

DvD Power Cord Confirmed. I repair about 15-20 xboxs a week here in San Diego,
and I came across one that had this 0031 Error Code today. I am just confirming
that I repaired it just by switching out the dvd power cord. Easy $50.