Xboxexperts.com Official Store

USA Status - IN STOCK (Most orders shipping within 24 hours)

This is our newest revision of the Hybrid eXtreme Uniclamp™ X-Clamp Repair Kit it includes all necessary tools, like screwdrivers, opening tools, and a 5mm metal drill and sand paper for the standoffs, as well as two alcohol wipes to clean off the chip dies!
Furthermore we added some additional eXtras which will further help the cooling of your console and increase the lifetime of the fix, you now get our RAM Pad Cooling Kit and 2 RAM heatsinks as well as 1g of our eXtreme Cool 360 Thermal Compound.
This kit is a compilation of all tools required for the hybrid fix and saves you the money buying these tools separately, over all you would otherwise pay around 40$ for all the parts you get here.

Includes:
-Hybrid eXtreme Uniclamp(TM) backplate with eXtreme-Cool 360(TM) Thermal Pads for CPU/GPU.
8x M5 14mm perfect fit cheese-head metric screws and 40x M5 1mm steel washers
1 gram eXtreme-Cool 360(TM) Gaming Thermal Compound (nano-carbon technology)
1x set Xbox 360 Hybrid eXtreme Foam Shims(TM) GPU&CPU (upgraded for 2011)

New Included Tools and eXtras:
2x RAM/Chipset Aluminum Heatsinks
1x eXtreme-Cool 360(TM) Thermal Pad RAM Cooling Kit 6 pieces (for Ram under GPU heatsink and under mobo)
-Xbox 360 Opener Tool
-Torx T8 and T10 L key
-> The L key can also be used for xbox 360 wireless controllers(got a hole in the middle), and it of course works for all types of case screws, the bigger T10 ones, as well as the small T8 ones(The old red screwdriver isnt in it anymore)
1x sheet of sand paper (to level standoffs in older units)
1x 5mm steel drill bit (needed for enlarging screw holes)
2x alcohol prep wipes (for prepping chips/heatsinks)

USA Status - IN STOCK (Most orders shipping within 24 hours)

Hybrid eXtreme Uniclamp™ X-Clamp Repair Kit (complete w/paste)

Named after the "Extreme" version of "Team HYBRID's Ultimate X-Clamp Fix"(cc).

Fixes most common 3 RROD errors and cool the 360 at the same time.

Now comes WITH 1gram eXtreme-Cool 360™ Thermal Compound ($2.99 value). Nano Carbon based thermal compound designed for the xbox 360 and other gaming consoles. Thermal conductivity >4.5w/mK.

Features the Xbox 360 Hybrid eXtreme Uniclamp™ backplate with eXtreme-Cool 360™ Thermal Pads.

eXtreme-Cool 360(TM) Thermal pads help transfer heat from under the GPU/CPU to the metal chassis. Two smaller thermal pads are included for filling the air gap between the RAM and GPU heatsink.

3M thermal tape ensures the pads won't fall off like competitors imitation models.

Hybrid eXtreme Foam Shims™ for the CPU/GPU made from high quality rubber infused foam composite material that provides the correct pressure and stability. The shims help ensure proper heatsink alignment and protect the dies from cracking due to excess pressure. The shims also spread the pressure from the heatsink over the entire bga chip helping to hold the solder balls in place by preventing lifting/warping at the corners of the chips caused by uneven pressure and several heat/cooling cycles.

This kit contains:
1x Hybrid eXtreme Uniclamp™backplate with eXtreme-Cool 360™ Thermal Pads.
8x M5 14mm perfect fit cheese-head screws
40x M5 1mm steel washers
2x eXtreme-Cool 360™ Thermal Pads for the RAM under the GPU heatsink
1x set Xbox 360 Hybrid eXtreme Foam Shims™ GPU&CPU (upgraded for 2011)
1 gram eXtreme-Cool 360™ Thermal Compound (enough for 3-4 consoles)

This kit requires drilling through the metal chassis for correct installation (drill bit available seperately).

Xbox-experts.com does not make any "no-drill" uniclamp since there is only about 3.75mm between the motherboard and metal chassis making it impossible to clear a screw head, the uniclamp and 2 washers. Any no-drill version would put dangerous pressure on the underside of the motherboard and possibly lead to irreparable damage.

The Hybrid eXtreme Uniclamp™, and the eXtreme-Cool 360™ product line described and their design/uses are the intellectual property of the owners of Xboxexperts.com, protected by Common Law trademark rights, and the federal "Lanham Act" (15 USC § 1125); prohibition against commercial misrepresentation of source or origins of goods.

USA Status - IN STOCK (Most orders shipping within 24 hours)

Hybrid eXtreme Uniclamp™ X-Clamp Repair Kit (WITHOUT Paste)

Nicknamed the "Extreme" version of "Team HYBRID's Ultimate X-Clamp Fix". We feel this is the most complete/advanced fix to date, and thank anyone who helped along the way. Now you can fix the 3 rrod and help keep the 360 cooler at the same time. This kit comes WITHOUT thermal paste.

Some of the highlighted upgrades in the new kit:

- Xbox 360 Hybrid eXtreme Uniclamp™ with eXtreme-Cool 360™ Thermal Pads, replacing the previous foam pads on the 2009 version. Some have measured GPU temp drops as much as 6C (results may vary) after installing the kit. Easily Fixes most common 3 RROD errors and prevents future ones.

This kit contains:
1x Hybrid Extreme Uniclamp
8x M5 14mm cheese-head screws
42x M5 1mm steel washers
2x Thermal pads for the RAM under the heatsink
1x New GPU-Foam shim upgraded
1x CPU Foam-Shim

Xbox SLIM Hybrid eXtreme Uniclamp™ X-Clamp Repair Kit (complete w/paste)

Only for Xbox Slim!!!

Named after the "Extreme" version of "Team HYBRID's Ultimate X-Clamp Fix"(cc).

Fixes most common red light errors and cool the 360 at the same time.

Features the Xbox 360 Hybrid eXtreme Uniclamp™ backplate with eXtreme-Cool 360™ Thermal Pads.

eXtreme-Cool 360(TM) Thermal pads help transfer heat from under the GPU/CPU to the metal chassis. Two smaller thermal pads are included for filling the air gap between the RAM and CGPU heatsink.

This kit contains:
1x Xbox 360 Slim Hybrid eXtreme Uniclamp™ Plate with eXtreme-Cool 360™ Thermalpads.
1x eXtreme-Cool 360™ Thermal Paste (Nano-Carbon Technology)
4x M5 14mm Metric Machine Screws
12x M5 1mm Steel Washers
12x M5 1,15 mm SPECIAL Washers(especially made for that purpose)

This kit requires drilling through the metal chassis for correct installation (drill bit available seperately).

The Hybrid eXtreme Uniclamp™, and the eXtreme-Cool 360™ product line described and their design/uses are the intellectual property of the owners of Xboxexperts.com, protected by Common Law trademark rights, and the federal "Lanham Act" (15 USC § 1125); prohibition against commercial misrepresentation of source or origins of goods.

USA Status - IN STOCK (Most orders shipping within 24 hours)

Xbox 360 Hybrid eXtreme Uniclamp™

This is our new Uniclamp for the Extreme version of "Team HYBRID's Ultimate X-Clamp Fix"(cc).

Features new eXtreme-Cool 360™ Thermal Pads which convert the uniclamp and metal chassis to a passive heatsink. This helps control thermal runaway problems during extreme gaming sessions, lowering core temps up to 6C.

Support can be found on the forums

This kit contains only the Hybrid foam shim pack for use with the "Team HYBRID's Ultimate X-Clamp Fix"(cc) tutorial.

Xbox 360 Hybrid eXtreme Foam Shims(™) for GPU and CPU chips - help even out pressure over entire chip and protect the die from damage/cracking by promoting parallel alignment between the heatsink and die. Has a layer of adhesive to hold them securely in place during install. Replaces the need for credit card strips mentioned in the tutorial.

Note: Made from special closed-cell foam to prevent overheating that would be caused by trapped air if cheap craft foam was used.

Support can be found on our forums.

USA Status - IN STOCK (Most orders shipping within 24 hours)

eXtreme-Cool 360™ Thermal Pads

- Includes one CPU (30x30mm) pad and one GPU (35x35mm) pad

- 2 pads for the upper ram chips that rest under the GPU heatsink to
close the air gap normally present.

- Upgrade your old Hybrid Advanced Uniclamps to the eXtreme version.
Just peel off the old foam pads and put these in place instead.

- Same thermal pads used in the Hybrid eXtreme Uniclamp™ kit.

- Draws heat away from chips to use chassis as a passive heatsink.

- Higher thermal conductivity and lower resistance than air or the foam
pads.

- Selected from a range of materials to give best thermal performance
and provide just the right pressure under the chips.

- Can also be used for homemade versions of the Hybrid fix.

- Adhesive on the backside to ensure pads stay in place.

This is a kit containing all the necessary screws(4x M2 10mm), nuts(4x M2) and the NEW SB X-Clamp Fix plate.

With this kit you can fix many Southbridge related errors like E73 0021 and some other errors that can eb SB related like E71.

You can find the tutorial here: http://xbox-experts.com/sbfix

Xbox SLIM Hybrid eXtreme Uniclamp™ X-Clamp Repair Kit (complete w/paste)

Only for Xbox Slim!!!

Named after the "Extreme" version of "Team HYBRID's Ultimate X-Clamp Fix"(cc).

Fixes most common red light errors and cool the 360 at the same time.

Features the Xbox 360 Hybrid eXtreme Uniclamp™ backplate with eXtreme-Cool 360™ Thermal Pads.

eXtreme-Cool 360(TM) Thermal pads help transfer heat from under the GPU/CPU to the metal chassis. Two smaller thermal pads are included for filling the air gap between the RAM and CGPU heatsink.

This kit contains:
1x Xbox 360 Slim Hybrid eXtreme Uniclamp™ Plate with eXtreme-Cool 360™ Thermalpads.
1x eXtreme-Cool 360™ Thermal Paste (Nano-Carbon Technology)
4x M5 14mm Metric Machine Screws
12x M5 1mm Steel Washers
12x M5 1,15 mm SPECIAL Washers(especially made for that purpose)
1x X-TOOL Ultimate Xbox 360 Slim Opener Unlock Tool(12-Parts, the only one that doesn't damage your xbox, Value: $12)
2x Thermal Pads for the RAM.
2x Aluminium RAM Heatsinks
1x 5MM High Quality Steel Metal Drill
2x Alcohol Wipes, to clean off the old thermal paste
This kit requires drilling through the metal chassis for correct installation (drill bit available seperately).

The Hybrid eXtreme Uniclamp™, and the eXtreme-Cool 360™ product line described and their design/uses are the intellectual property of the owners of Xboxexperts.com, protected by Common Law trademark rights, and the federal "Lanham Act" (15 USC § 1125); prohibition against commercial misrepresentation of source or origins of goods.

BACK IN STOCK AND READY TO SHIP

A complete redesign of the best selling Matrix Glitcher, The Glitcher II was developed on the ground of the countless feedbacks received from our customers and official resellers during the previous months.

The Matrix Glitcher II does not need anymore to be programmed before it can be used. It already contains all the software code necessary to work with all the Glitchable models of FAT and SLIM Xbox360 at the date of the release of the product.

The selection of the console type and model is done simply by positioning the Switches present on the Glticher II in the position indicated by the installation manual.

One of the biggest issue faced by installers was the different behavior of the same models of Xbox360. To help them overpass this we added the the possibility to be connect the Glitcher II to a PC using the same Matrix External programmer already available with our Matrix Freedom PCB. Once connected to the PC it is possible to use the fine tuning software to try and identify the best timings for his own console.

Installation diagrams and tutorials are available in the Download section on infinitymod.

• Booting of unsigned code on Xbox 360 and XBOX360 slim
• Preprogrammed with a brand new and advanced Matrix Glitching code.
• Compatible with all Xbox360 SLIM and FAT models (except Corona and Xenon motherboard)
• On board switch to quickly select console type and model.
• Future-proof updateable with external USB programmer (not included).
• After-installation fine tuning of glitch timings to better fit each different console (external USB programmer needed)
• Quick installation (7 Wires on Slim or 6 Wires on Phat)
• Compact PCB size with easy to solder pads.
• Unique Serial code identification for each Glitcher II verifiable online.

-- Out of Stock in USA --

Cost effective NAND reader / programmer to complete the GliGli Hack.

It features a PIC18F2455 microcontroller for stable and quick reading/writing of all NAND models available on the different XBOX360 models.

The Matrix NAND programmer is also fully compatible with NANDPRO 2.0e and several other third party programming tools.

• Fast USB SPI 360 NAND programmer!
• Fully compatible with all XBOX360 NAND models.
• Fully compatible with NandPro2.0e Software and other third party software.
• Easily reprogrammable with via USB connector.
• Quick reading and writing times.
• Microchip based for enhanced stability.

-- Out of Stock in USA --

This is a Maximus 360 Power Dongle it can be used to power your Xbox 360 DVD-Drive using your PC's power supply(molex), it is equipped with an eject button and a button to put hitachi drives in mode-b.

-- Out of Stock i USA --

The World FIRST HARDWARE FLASHER

More than a year of research and development was poured into Maximus Lizard and today this bad ass lizard has seen the light and come packed with really cool technology. The Dream of every DVD Firmware Tester has come true. And Do you Know What That Means?

No more:
Sata Drivers
Win64 Problems
PC Hanging
PC Forced Reboot
Multiple Computers to cover all drives

Its time to start in the Lizard Way. Your PC fades into the dark as you enjoy freedom like never before! Lizard equals FREEDOM. With Lizard, you are investing in a professional TOOL that will not be limited to a few quantity of drives. Also there is NO RESTRICTION on the kind of file you can open, read or write.

At Maximus, we take engineering seriously. You can trust that Maximus Lizard rely on a deep research and lots of time prototyping. and will offer you RELIABLE FREEDOM LIKE YOU'VE NEVER HAD BEFORE !!

LIZARD FEATURES ARE TRUE FEATURES! With Maximus Lizard, you won't have another tool in the background doing the real flashing work, this is because the Lizard features are built right into the hardware device itself.

- Hardware Flasher with Unlock, Read, Write, Erase, Key Retrieval
- Support all Xbox 360 Drives, Samsung, Hitachi, Benq, Liteon, and Slim Liteon. (yes it also unlock and read keys on the latest 0225)
- Built in support for many PC DVD Sata Drives too
- Support Onboard AES 128 Key Verification
- Several Modes of Operation: Use it with your PC or as StandAlone (*)
- Micro SD Card Slot for file storage
- Upgradeable Onboard Firmware
- Expand the functionality with his Accesory Port, several Accesories are on design bench already
- Sexy Graphical Screen Display
- Friendly Navigation Menu with simplified button count
- Multilingual Menu
- Free PC companion Software

* Full Stand alone mode will be implemented in stages with firmware updates
** Some features might not be available at launch, but will be available later with a firmware update

This is a Special iHas124B Revision DVD-Writer(or compatible model) flashed with iXtreme Burner Max Firmware, suitable for burning 8.7GB backups onto Verbatim DVD+R DL 8.5GB DVDs.

You need one of these to burn legit XGD3 backups for iXtreme LT+ 3.0 DVD-Drives.

This is the Payload Version of this Burner.

You can use this to burn XGD3 backups, however you need to use the Payload Tool each time before you burn.

This is a very special DVD-Writer you should know already what it means if you're reading this.

It is exactly like a B Model of the lHas DVD Writers, perfect for XGD3 out of the Box, this means you do NOT have to use the Payload Tool!

Also it is Brandnew! Not a super old B Model DVD-Writer, they are over a year old now + the Sony DVD-Writers are a lot more reliable than the Lite-0n DVD-Writers, they are more reliable and the lasers do not die as quickly

Easy to use, non-corrosive, and extreme performance make ec-360 an ideal thermal interface material for all gaming comsoles or gaming PCs. Specifically designed for the cooling needs of the Xbox 360 and other gaming machines. Offers highest possible Price/Performance ratio. Designed/tested in USA and Germany and mixed/packaged overseas according to our specs.

Over 1/3 gram of extreme thermal conductive pure Nano-Carbon compounds per syringe blended in a base of other nanometer sized metal oxide particles (silver/aluminum/boron/zinc) and small amount of organosiloxane compounds for ultimate stability and thermal conductance.

Low bleed, non-flowing and low evaporation mean it will not run all over the place or dry out over time. Although it is non viscous, it is very easy to spread out over chips and cleans up easy compared to many other brands.

Extreme operating temperature range....stable performance from -55~300°C without degradation in performance.

With a very high Dielectric constant, it will not short out components...can withstand above 10,000 volts without causing a short!

Low thermal impedance (<0.067-in2/W) is achieved by utilizing an extremely thin bond line at the junction, divided by high thermal conductance (4.5 W/Mk), plus low interfacial resistance equals high efficiency. Lower thermal impedance results in lower junction temperatures. The lower the thermal impedance, the more efficiently heat travels from the heat source to the heatsink.

Lead Free and RoHS/SGS/MSDS certified (test results available upon request)

Although the compound is totally non-toxic, please mind the following:

Use as a thermal interface material ONLY

Keep out of the reach of children

Avoid contact with skin and eyes. If contacted, flush with water and get medical attention if irritation persists.

Do not ingest or put into mouth. If ingested, do not induce vomiting. Rinse mouth and seek medical attention.

The standard price will be starting from 2.99 $US. Buy higher quantities and save.

For the first week you will be able to get it from 1.99 $US so hurry up and save yourself a bargain :)

Some feedback on the paste would be nice you can post your thoughts here, thank you :)

http://forums.xbox-experts.com/viewtopic.php?f=4&t=4883

Stock status good, shipping within a few days!

BIG BULK PACKS, about 4 times as much like the normal ones!

These packs are a fair bit bigger than the smaller ones, note this paste is mainly made of carbon which is very light, so it is a lot more paste than arctic silver for example at 4g.

Easy to use, non-corrosive, and extreme performance make ec-360 an ideal thermal interface material for all gaming comsoles or gaming PCs. Specifically designed for the cooling needs of the Xbox 360 and other gaming machines. Offers highest possible Price/Performance ratio. Designed/tested in USA and Germany and mixed/packaged overseas according to our specs.

Over 1.5 gram of extreme thermal conductive pure Nano-Carbon compounds per syringe blended in a base of other nanometer sized metal oxide particles (silver/aluminum/boron/zinc) and small amount of organosiloxane compounds for ultimate stability and thermal conductance.

Low bleed, non-flowing and low evaporation mean it will not run all over the place or dry out over time. Although it is non viscous, it is very easy to spread out over chips and cleans up easy compared to many other brands.

Extreme operating temperature range....stable performance from -55~300°C without degradation in performance.

With a very high Dielectric constant, it will not short out components...can withstand above 10,000 volts without causing a short!

Low thermal impedance (<0.067-in2/W) is achieved by utilizing an extremely thin bond line at the junction, divided by high thermal conductance (4.5 W/Mk), plus low interfacial resistance equals high efficiency. Lower thermal impedance results in lower junction temperatures. The lower the thermal impedance, the more efficiently heat travels from the heat source to the heatsink.

Lead Free and RoHS/SGS/MSDS certified (test results available upon request)

Although the compound is totally non-toxic, please mind the following:

Use as a thermal interface material ONLY

Keep out of the reach of children

Avoid contact with skin and eyes. If contacted, flush with water and get medical attention if irritation persists.

Do not ingest or put into mouth. If ingested, do not induce vomiting. Rinse mouth and seek medical attention.

The standard price will be starting from 2.99 $US. Buy higher quantities and save.

For the first week you will be able to get it from 1.99 $US so hurry up and save yourself a bargain :)

Some feedback on the paste would be nice you can post your thoughts here, thank you :)

http://forums.xbox-experts.com/viewtopic.php?f=4&t=4883

eXtreme-Cool 360™ Thermal Pad RAM Cooling Kit for Xbox 360 (6 pieces)

Replacement thermal pads for the xbox 360 RAM chips on the underside of the motherboard.

Up to 300% more thermally conductive than the old OEM pink thermal pads.

Use to replace old torn pads, or on boards that never came with them to help keep the RAM cooled off. Transfers heat from the chips to the metal chassis of the 360.

They are the perfect thickness to not stress or flex the motherboard (unlike other brands which may be too thick or made from insulative materials) while still being highly efficient at transferring heat.

Same great quality thermal pad material which is used on the Hybrid eXtreme Uniclamp™.

Two thermal pads are included for the 2 upper ram chips to fill the air gap which is slightly over 1mm wide between the RAM and GPU heatsink.

*Not needed in newer units with all RAM chips on the upper side of the board.

Directions:

Step 1:
Remove any old thermal pads and clean the RAM chips with isopropyl alcohol and a q-tip or lint-free cloth. Let dry.

Step 2:
Gently peel off the white layer on the bottom covering the 3M adhesive.

Step 3:
Carefully place one pad on each of the 4 bottom RAM chips with the adhesive layer facing down. Press gently down on each pad in a circular motion to ensure the pressure sensitive adhesive makes a secure connection to the RAM and to remove any air bubbles.

Step 4:
Gently peel off the top clear protective layer. optionally add a drop of thermal compound to each pad.

Step 5:
Reinstall motherboard.

Step 6:
Install 2 thin pads on the upper RAM normally hidden by the gpu heatsink.

Pads can be reused as long as kept undamaged and clean. Easy to remove pads if warmed up first.

Xbox 360 Ramsinks (RAM / HANA /ANA / Southbridge heatsinks) 4-Pack

- High quality aluminum heatsinks intended for use on Xbox 360 RAM memory chips, HANA/ANA, and Southbridge chips.

- Strong 3M thermal adhesive layer on bottom ensures they don't fall off when properly installed. Don't worry about them falling off inside the case when the 360 rest vertically.

- Dissipates heat from the chips to help prevent overheating (less chance of RAM or E74 related errors)

- Multiple extended fins provide maximum cooling surface area

*Minor modification of one heatsink may be required to fit when the GPU heatpipe is in the way. Simply hold the heatsink with pliers and use a dremel w/ cutoff wheel in other hand to trim a few fins off.

Installation:

Step 1:
Clean off any dust/residue on the RAM, HANA/ANA, and Southbridge chips with 99% isopropyl alcohol. Let dry.

Step 2:
Peel off the protection layer from the bottom of the heatsink to reveal the adhesive. Be careful to not touch the adhesive or get it dirty or it will become less adhesive.

Step 3: Carefully place one heatsink on each chip and press straight down from above to activate the pressure sensitive adhesive. Make sure the heatsinks are facing the right direction (as shown in the pics) to ensure maximum airflow across the fins.

Step 4: For proper removal DO NOT just rip off from the chips or you may damage the solder connections in the process. Use a heatgun on low temp to warm up the heatsinks first, then gently pull/wiggle until it releases. Store on a piece of wax paper to keep the adhesive clean until ready to use again.

* The more times you re-use, the less sticky the adhesive will become.

This is a 50mm Addon Fan for use in your Xbox, it is of the small type(50mm) and can be put in the bottom of the case for example, or in front of the GPU or CPU heatsink to provide it with a fresh airflow.
To power them just connect to the 12V points under the PSU(In the tutorials section there is a guide showing which voltage to get from which spot).
They are of the quiet sort :)

They come with a regular 3-Pin Fanheader, so can also be used in PCs or if you built a custom fan header.

This is a 70mm Addon Fan for use in your Xbox, it is of the bigger type(70mm) and can be put on top of the small GPU extension heatpipe for example, or in front of the GPU or CPU heatsink to provide it with a fresh airflow.
Or many people also use these as an air intake fan and cut a hole into the chassis.
To power them just connect to the 12V points under the PSU(In the tutorials section there is a guide showing which voltage to get from which spot).
They are of the quiet sort :)

They come with a regular 3-Pin Fanheader, so can also be used in PCs or if you built a custom fan header.

This is a pack of 8x M5 Machine screws, the same ones used in the Hybrid Kits, they are compatible with the Xbox 360's heat sink holes.
Unlike many screws in the UK and U.S these screws are actually real metric screws which is important as the xbox chassis design is metric so using screws or other parts measured in fractions of inches is always inaccurate.

These screws are made in Germany imported into the U.S from our European office, made from high quality steel and they are zinc coated to protect them from corrosion.

Details:
Length: 14mm
Diameter: 5mm
Type: Pan-Head

This is a pack of 8x 16mm M5 Machine screws, the same ones used in the Hybrid Kits, they are compatible with the Xbox 360's heat sink holes.
Unlike many screws in the UK and U.S these screws are actually real metric screws which is important as the xbox chassis design is metric so using screws or other parts measured in fractions of inches is always inaccurate.

These screws are made in Germany imported into the U.S from our European office, made from high quality steel and they are zinc coated to protect them from corrosion.

Details:
Length: 16mm
Diameter: 5mm
Type: Pan-Head

This is a pack of 40x M5 1MM Metal washers like required for the Xbox 360.
These are good for the Hybrid fix and any general application for a fix, they are metric, no crappy washers with a big threshold or measured in fractions of inches leading to inaccuracies.
Made from high quality steel to be durable, unlike nylon washers these washers are also good for x-clamp fixes as steel does not deform under the heat over time like nylon does which is what you want to avoid for a longer lasting fix because it influences the tension of the screws.

Details:
Density: 1MM
Inner diameter: 5.3MM

High Temperature Tape, this kind of tape is used to attach temp probes, can be used for insulation for Oven Reflows and much more.

Size: 10mm Roll

Brandnew Digital Multimeter/Voltage/Resistance Checker, used to check voltages, resistances and much more, perfect for general electronic usage and specifically Xboxes.
High quality at a low price, we use it ourselves too.

Comes with a printed manual, 2 sensors and a battery is included as well.

This is a brandnew Philips Lite-On DG-16D2S DVD-Drive, it is flashed with standard firmware, this is the very latest and most reliable version of Xbox 360 DVD-Drives, thus why it is so popular as a replacement drive.

Can be used for Dirty Disk errors, if you get reading errors in general and the like.

Not available in U.S at the moment, will be shipped by DHL from Europe(Germany), please send an email to: sales@xboxexperts.com if you need this part, we will set up an invoice for you

Brandnew HANA X802478-003 Chip Preballed with Leaded Solder balls, 100% new, tested and working, warranty, if it doesnt work you can ship it back and get a refund.

This chip is used for Zephyr, Opus, Falcon, Jasper und Xbox Slim/Valhalla Chipsets/Mainboards, all HDMI mainboards/consoles.

Not available in U.S at the moment, will be shipped by DHL from Europe(Germany), please send an email to: sales@xboxexperts.com if you need this part, we will set up an invoice for you

Brandnew XSB X02047-027 Southbridge Chip Preballed with Leaded Solder balls, 100% new, tested and working, warranty, if it doesnt work you can ship it back and get a refund.
This one can be used for Xenon, Zephyr, Opus and Falcon type Chipsets/Mainboards.

Not available in U.S at the moment, will be shipped by DHL from Europe(Germany), please send an email to: sales@xboxexperts.com if you need this part, we will set up an invoice for you

Brandnew PSB X817692-002 Southbridge Chip Black Preballed with Leaded Solder balls, 100% new, tested and working, warranty, if it doesnt work you can ship it back and get a refund.
This one is used on Jasper and Xbox Slim chipsets/Mainboards.

--Not in Stock in USA--

This is a brandnew 1893BFLF Network chip it is the newer version which is compatible for both versions of the ICS type network chips used in Xbox 360s, you can also use it to replace the ICS 1893AFLF chips, the PCB requirements are the same.

It is a brandnew one(coming in a sealed package from the factory ready to be soldered) and can be used for network chip issues, like E77 E76 E75 and in some cases E73 as well.

Here is a little video that shows how to solder chips like that:
http://www.youtube.com/watch?v=6YU3v_w7x7o

This is a brandnew BCM5241 Network chip, the small square black one, which is extremely, difficult, in fact almost impossible to get, however we managed to get them in the end :), it is widely used in all Xbox 360 mainboard revisions.

It is a brandnew one(coming in a sealed package from the factory ready to be soldered) and can be used for network chip issues, like E77 E76 E75 and in some cases E73 as well.

This is a brandnew NTD T60 N02RG MOSFET, these are nowadays pretty much impossible to get since they are not made anymore since 2007 already.

The MOSFETs are brandnew and still sealed in the package ready to be soldered on. This one can mostly be found on Xenon and Zephyr type Xbox 360 mainboards.

This is a brandnew NTD 85 N02G MOSFET, these are nowadays pretty much impossible to get since they are not made anymore since 2007 already.

The MOSFETs are brandnew and still sealed in the package ready to be soldered on. This one can mostly be found on Xenon and Zephyr type Xbox 360 mainboards.

This is a brandnew STD D70N0 2L MOSFET.

The MOSFETs are brandnew and still sealed in the package ready to be soldered on. This one can mostly be found on Falcon, Opus and Jasper type Xbox 360 mainboards.

This is a brandnew IR LR3715Z P635G MOSFET.

The MOSFETs are brandnew and still sealed in the package ready to be soldered on. This one can mostly be found on Falcon, Opus and Jasper type Xbox 360 mainboards.

This is a brandnew 220uF 10V Capacitor widely used in Xbox 360 consoles.

The Capacitors are brandnew, ready to be soldered on. Good for replacing burned capacitors during reflows etc. This one can mostly be found on Xenon, Zephyr, Falcon, Opus and Jasper type Xbox 360 mainboards.

*It might not look exactly like on the picture but these are new and you can be sure to get a compatible one

This is a brand new 820uF 6.3V Capacitor compatible replacement widely used in Xbox 360 consoles.

The Capacitors are brand new, ready to be soldered on. Good for replacing burned capacitors during reflows etc. This one can mostly be found on Zephyr, Falcon, Opus and Jasper type Xbox 360 mainboards.

*It will not look exactly like on the picture, you will get 1500uF ones these are new and they are definitely compatible, the capacity/voltage written on the capacitors is always only the maximum it can take, so 1500uF ones work perfectly fine, they just got more "power", 820uF ones will follow some time in the future when we find them at a proper price.

This is a brandnew 1500uF 16V Capacitor widely used in Xbox 360 consoles.

The Capacitors are brandnew, ready to be soldered on. Good for replacing burned capacitors during reflows etc. This one can mostly be found on Zephyr, Falcon, Opus and Jasper type Xbox 360 mainboards.

*It might not look exactly like on the picture but these are new and you can be sure to get a compatible one

This is a brandnew 2700uF 16V Capacitor widely used in Xbox 360 consoles.

The Capacitors are brandnew, ready to be soldered on. Good for replacing burned capacitors during reflows etc. This one can mostly be found on Xenon type Xbox 360 mainboards.

Philips Lite-On DG-16D2S DVD Drive flashed with iXtreme 0800 v3 firmware(Liteon AP25V3). Intended to be used as a dedicated "ripping" drive for creating Xbox 360 game backups. Just connect to a PC connection via sata or sata-usb converter and the drive is automatically detected by Windows. Powers direct to 0800 mode to be used with the popular "Xbox Backup Creator" backup program which allows you to rip complete game ISO files with full support for SS V2, XGD2, and XGD3 including correct AP2.5 topology data.

These drives are from a very reliable source which provides us with "factory inspected OEM pulls". Many are still in unused condition with manufacture dates of 2011. After we receive them, they are completely inspected/serviced/tested by us. If needed we do a full cleaning, laser power adjustment, drive belt replacement, re-greasing, whatever it takes to get the drives to "near-new" condition.

Each drive is tested with Xbox Backup Creator to ensure they can rip all the latest games without a hitch. They are tested to read both retail and backup discs (DVD+R DL) to ensure your backups can be properly read if needed.

After testing, we apply our in house warranty and quality check stickers so you know your drive was properly inspected and tested. In USA, all 0800 drives come with a 60 day replacement warranty. If the drive stops reading games, you can send it in for a replacement, customer just pays for shipping. If the drive has been opened or firmware reflashed, warranty is void.

How to power your drive: To use with your computer, you will have to either get a power supply with a molex-xbox 360 power adapter or use an Xbox 360 to power it.

You can use a Sata-USB converter to access the drive via any USB connection for convenience.

Checking/patching your ISO backup file:
For maximum compatibility we recommend running all iso files through a check with abgx360 as recommended by C4eva, "All necessary stealth practices still apply, and it remains the responsibility of the user to verify the stealth of their ISOs with abgx360." Even though the latest stealth patches are very good, there is always a risk of being detected and banned from xbox live if you are detected running backups, so play on live at your own risk.

Download abgx360:
http://abgx360.net/download.php

How to burn your 0800 drive generated backup (iso):

For burning we recommend using imgBurn with the iXtreme Burner MAX firmware V1.0 for the following Liteon iHAS drives:

Liteon iHAS124B = baseline model
Liteon iHAS224B = 124 + LightScribe
Liteon iHAS324B = 124 + SmartErase
Liteon iHAS424B = 124 + LightScribe + SmartErase (or = 224 + SmartErase)
Liteon iHAS524B = 124 + LabelTag + SmartErase
Liteon iHAS624B = 124 + LabelTag + LightScribe + SmartErase (or = 524 + LightScribe)

This is the only firmware/burner combo that supports full 8.7GB backups on regular dual layer DVD+R DL discs with no CIV errors and still passes all current checks.

Download iXtreme Burner MAX firmware V1.0: http://hotfile.com/dl/133005649/08f40be/iXtreme_Burner_Max.rar.html

Tutorial: How to crossflash iHas drives to unlock all features including Burner Max
http://www.ixtreme.net/xbox-360-tutorials/18465-unlock-all-ihas-features-bare-bone-drives-crossflashing-tutorial-2.html

Tutorial: How burn/check xgd3 with Imgburn 2.5.6.0 & KProbe 2

http://www.ixtreme.net/open-forum/17835-how-i-burn-check-xgd3-using-imgburn-2-5-6-0-kprobe-2-a.html

Legality: Can I backup my computer (xbox360) software?

Yes, under certain conditions as provided by section 117 of the Copyright Act. Although the precise term used under section 117 is “archival” copy, not “backup” copy, these terms today are used interchangeably. This privilege extends only to computer programs and not to other types of works.

Under section 117, you or someone you authorize may make a copy of an original computer program if:

-the new copy is being made for archival (i.e., backup) purposes only;
-you are the legal owner of the copy; and
-any copy made for archival purposes is either destroyed, or transferred with the original copy, once the original copy is sold, given away, or otherwise transferred.

Is it legal to sell backup copies of computer software (in online auctions or on website)? Is it legal to buy and use a backup copy of software I already own?
No. The Copyright Act does not permit anyone to sell backup copies to third parties separately from the original copy of the software. If you lawfully own a computer program, you may sell or transfer that lawful copy together with a lawfully made backup copy of the software, but you may not sell the backup copy alone.

We have been made aware of websites that are offering to sell “backup” copies of software via download over the Internet or in a custom-burned CD-R format, under the guise that section 117 permits this. Section 117 does NOT permit the sale of backup copies. Again, section 117 does not allow you to sell backup copies to someone else except when such backup copies are sold together with the original lawfully owned copy. It does not allow anyone to solely distribute “backup” copies to the public. In addition to being a violation of the exclusive right of distribution, such activity is also likely to be a violation of the terms of the license to the software. In many cases these sites appear to be a front for distribution of illegal copies, which is copyright infringement. You should be wary of sites that offer to sell you a backup copy.

And if you do buy an illegal backup copy, you will be engaging in copyright infringement if you load that illegal copy onto your computer, i.e., the unauthorized reproduction of the infringing computer program into memory. Lesson: if you want a backup copy of a lawfully owned computer program, back it up yourself.
http://www.copyright.gov/help/faq/faq-digital.html

This is a refurbished(new laser etc.) Hitachi-LG GDR 3120L DVD-Drive, it is flashed with standard firmware, it is one of the first generation of Xbox drives and was used widely in Xenons.

Can be used for Dirty Disk errors, if you get reading errors in general and the like.

This is a refurbished(new laser etc.) Toshiba-Samsung TS-H943A MS25/28 DVD-Drive, it is flashed with standard firmware, it is one of the first generation of Xbox drives and was used widely in Xenons.

Can be used for Dirty Disk errors, if you get reading errors in general and the like.

This is a refurbished(new laser etc.) Philips-BenQ VAD6038 DVD-Drive, it is flashed with standard firmware, it is one of the first generation of Xbox drives and was used widely in the first HDMI consoles.

Can be used for Dirty Disk errors, if you get reading errors in general and the like.

This is a brandnew Philips Lite-On DG-16D4S DVD-Drive, it is a DVD-Drive with 9504 Firmware, so that means it is unlocked and can very easily be flashed. This DVD-Drive is only for the Xbox 360 Slim.

Can be used for Dirty Disk errors, if you get reading errors in general and other issues too, most people will be interested in it for flashing though. :)

--Out of Stock in USA--

This is a suitable replacement laser for all Hitachi-LG GDR 3120L(0032, 0047, 0059, 0078, 0079) and Toshiba-Samsung(MS22/MS25/MS28) DVD-Drives.

Here you can find a video tutorial, on how to replace a laser in a DVD-Drive:

http://xbox-experts.com/tutorial/xbox-360-laser-lens-repair/

--Out of Stock in USA--

This is a suitable replacement laser for all Philips-BenQ VAD 6038 and Philips-Lite-On 16D2S(74850c, 83850c, 93450c) DVD-Drives.

Here you can find a video tutorial, on how to replace a laser in a DVD-Drive:

http://xbox-experts.com/tutorial/xbox-360-laser-lens-repair/

-- Out of Stock in USA --

This is a suitable replacement laser for all Philips-Lite-On 16D4S DVD-Drives for Xbox Slim.

Here you can find a video tutorial, on how to replace a laser in a DVD-Drive:

http://xbox-experts.com/tutorial/xbox-360-laser-lens-repair/

This is a metal drill bit like required for the Hybrid Fix to drill the 5mm holes into the chassis.
It is made from high quality hardened steel which assures a high durability.
In order to use it you need some kind of drilling machine, it might also work with certain "dremel"-like tools but dont take that as granted.

Details:
Diameter: 5mm
Material: Hardened Steel

Generic Xbox 360 opener tool. Use for easy opening of all "phat" models. Includes a torx T8 and T10 driver.

This is the NEW VERSION of the Opener Kits, it really contains all thats needed, the driver, also got a Torx T8 bit(with hole) so it can be used for the black heatsink screws as well as Xbox 360 Controllers(they need the hole).

In the other kits, like these, you only get a T10 which can only open the outer case screws, nothing else...
->
Old version Xbox 360 Opener Kits

This is a red Torx T8 Screwdriver, it can be used to disassemble the Xbox you can use it for all the tiny black screws, which attach the RF board or the heatsinks to the X-Clamp bolts.

Additionally it is perfect for Controller mods you can use it for the special torx screws used in xbox 360 controllers.

This is a small sheet of sand paper for metal application and can be used to sand down the standoffs as well as after drilling you can get rid of the metal chips around the holes.
The standoffs if not sanded are too high and cause flexing and the area around the holes should be nice and smooth so that the uniclamp plate/x-clamps are not elevated.

It is a 160 grit sheet of sandpaper with the sizes ~7cmx14cm

We have created a special tool for disassembling the Xbox 360 Slim console. As many of us allready know, opening the Xbox 360 Slim is not as easy as opening the Xbox 360 Fat. Disassembling the Slim is difficult and the shell can damage easily if the tools aren't right. Now with the X-TOOL everybody can open a Xbox 360 Slim, the whole process has become so easy and u don't have to be affraid that u damage your console. Your worries are over! This tool is a must for professionals and the people at home if they need to open a Xbox 360 Slim.
The X-TOOL is a set of 8 pieces of special customized tools and screwdrivers.

U need to open your Xbox360 Slim but still not convinced that X-TOOL is the tool for you?
Then check out the video!!!

Perfect for cutting/stripping cables, cramping and insulating afterwards.

- Universal Cable Stripping Tool
- No Damages to the inner conductor of the cables
- 2-in1 Tool: Integrated Wire Cutter
- Easy Removal of the outer cable coating
- Slip-proof handle
- Manufactured from High-Quality Plastic
- Suitable for Network, other Data-cables and standard cables.

Application:

Application as a Cable Cutter/Stripper with Electronics. Perfect to cut and strip thinner cables, like the ones used in electronics, on circuit boards or data cables in a computer, network cables, HDMI cables etc. Easy to use to cut cables and twist them together Wire Cramping.
Additionally you get a roll of electric tape to insulate the cables when you're done.