Details for Error code E21/0111
(unknown) probably NAND/RAM?
|Primary Error code:||3 RLOD|
|E-Code / Secondary Error code:||E21 (No Audio/Video) / 0111|
|Binary/Hex:||00010101 / 0x15 -> 21|
|No Known fixes available!|
Powered by Xbox-experts.com
This error is unknown but could be somehow related to a cold solder joint under the RAM.On xbox-scene there was also a post in which was claimed that it has to do with the NAND
Comments for this Error code:
gyilokka on 2014-11-28 22:11:26 :
Another GPU vote here, i was doing a RGH when 0111 hapend. I Couldnt boot up the
box, then i tought it should be a RROD, so wrote back orig nand BUMP 0111!
Removed heatshink from gpu applied presure on the corner(the one located between
cpu and hana) and green lights came up! The board is on my rework station now
waiting for a reflow.
So think about GPU first, when you face with this problem. Greetings from
A starter bga reworker with home made Arduino based rework system:)
max1zzz on 2013-04-10 17:55:25 :
just had a 0111, pressure on the gpu got it booting, reflowed and it is now
working fine ;)
Pseudo99 on 2013-01-23 12:05:35 :
Got this after I did a successful RGH on a Falcon. Happened intermittently.
Assumed the system needed a reflow, so I installed the same chip with identical
wire placement into another Falcon. Same thing started. After some googling, I
decided to move the placement of the D (CPU_rst) wire (was using shielded low
loss) away from the fans and closer to the heatsinks. I also moved placement of
my green wire on the underside of board just in case. Fixed the problem. The
chips were CR revision C, maybe it's something specific to them.
fantais on 2010-11-25 15:15:54 :
Got this error with Artifacts and Freezing symptoms, reflowed the GPU, works
jerkysmile on 2010-05-21 12:02:44 :
Might be too tight bolting of GPUCPU Heatsinks with unpluged or damaged
P.s Sry for grammar mistakes, from Russia with love :D
jerkysmile on 2010-05-21 12:02:24 :
might be too tight CPU and GPU Bolting with unplugeddamaged AVHDMI cable.
P.s sry for mistakes, from Russia with love :D
xboxJedi on 2010-02-21 18:22:32 :
I had the 3RROD with error 0111 and did the following: (NOTE: i have no warranty
and the seal was broken by someone else so do not do this unless you know what
REMEMBER TO CLEAN ALL OLD THERMAL PASTE OFF BEFORE DOING ANYTHING ELSE
REFLOW W/HEAT GUN, GRIDDLE & TEMP. GUN ON 4 RAM CHIPS/SOUTHBRIDGE &
THEN THE X-CLAMP FIX TO REPLACE THE CRAPPY X-CLAMPS AND SNUG EVERYTHING DOWN
its been running hours upon hours for me so i hope this helps!
Copyright Information: Lately it has come to our attention that more and more people stole content from this Error code Database without giving credit, some also restricted access to this information and demanded a payment, we would like to point out that it is perfectly fine to republish content from XE on other sites, however we demand a link back to this error code database and the information must be freely and non commercially available, we appeal to those who feel addressed, add a link and respect the work of others, thank you...
Notice: None of this is official, the methods have often been proven to work but success cannot be guaranteed, you do it on your own risk!
If your console is still covered by the 3 year warranty use it because Microsoft will fix it for free!
A lot of the information you are getting here has been collected in the community, so thanks to everybody who shared his misery!