Details for Error code E73/1021

Cold solderjoint - Ethernet/Southbridge



1 red lights

 
Details
Primary Error code:1 red lights 1 RLOD
E-Code / Secondary Error code:E73 / 1021
Binary/Hex:01001001 / 0x49 -> 73
Known fixes:

1) Southbridge X-Clamp-Fix
2) Reflow the Southbridge/Ethernet chip area
3) Check the area under the Southbridge for parts that might have fallen off and solder them back on.
4) In rare cases it can also be GPU related so an X-Clamp Fix might work as well (bigart666)

Related Errors:
Powered by Xbox-experts.com 
No Related Errors available!
Description:

This error is caused by a cold solder joint under the Southbridge or the ethernet chip.In rare cases it can also be triggered by a cold joint under the GPU on one of the lines that run to the Southbridge chip.
And missing parts(caps, resistors...) under the Southbridge can trigger this error as well.

References:

BJTech
bigart666

Clicks:274700
Share(BBCode):

 
 

Comments for this Error code:

JYP666 on 2012-10-03 11:22:28 :

I have had E73 many times on my Falcon Revision 1 board. Each time I let it
overheat then put pressure on the small Ethernet chip at the back left of the
console, just above the south-bridge. As with all XBox error's it can be a
million things but for me it was pressure on the Ethernet chip.

 

Swaste2004 on 2011-09-26 12:03:17 :

this is a link to my video
www.youtube.com/watch?v=U9n9RQ5T9Cs&feature=youtube_gdata_player

 

Swaste2004 on 2011-09-18 14:24:26 :

Hi all I have fixed my e73 by x-clamp fix. The trick is to just apply the right
pressure on the gpu its trail and error.I have drilled holes through my case so
i can adjust the heat-sink without oping. Too much pressure and e73 not enough
and overheat. Worked like a charm.

 

justchillin1981 on 2011-08-20 07:51:38 :

definately not a ethernet error.. its a video error gpu a ana or southbridge...

 

CasualGamerCC on 2011-08-05 06:30:19 :

Successfully repaired by reflowing Southbridge with ZT-7 station @ 250C on
display.

 

-SOCAL- on 2011-07-15 09:53:30 :

I bought a refurbished xbox 360 falcon motherboard and when i opened it up it
looked like the person who refurbished it rerouted the direction of some
electricty to another resistor/capacitor. on the motherboard it was marked e73
so i assume it had the e73 error. so if u lost one of the resistors and dont
have any extras i will take a picture to show u what he did

 

Ars on 2011-06-22 20:51:23 :

In some cases a defective AV-cable can cause the E73 error.

 

xbox-jedi on 2011-05-28 19:34:28 :

ATTENTION: We repair hundreds of consoles.. We recently found an E73 1021, took
it apart, only to find broken chips under the CPU because the customer tried
fixing it themselves,

therefore the board is JUNK and they get to buy a new xbox
:)

so this error isnt always just a reflow fix, it can mean MISSING CHIPS



 

MikeBartoli on 2011-01-05 14:14:57 :

Hey guys,
Lots of good info on here.. I got the E73 error on my box so I took the mother
board out to inspect it and found that two of the little (micro) caps have come
loose from the bottom of the larger processor (CPU?). I had to use a magnifying
glass to see what was going on and tried to handle the loose caps but they are
so small it's nearly impossible! Is this board junk now, what can I do?

 

Cvisser on 2010-11-30 03:19:45 :

@bigart666 Yeah did the same thing and it worked after letting it overheat. I
did the x clamp fix and still got the error so that doesn't mean its the
GPU. The Southbridge X-clamp-fix is what u need to do.

 

t360r on 2010-11-18 17:10:53 :

The proper way to Reflow the GPU HANA CPU is by using a BGA Rework Station this
uses Infrared and covers the whole area unlike a heatgun. I have Repaired a ton
of the E73 Error on Consoles along with E74 Error simply by using a BGA Rework
Station to do a Reflow then doing the X Clamp fix! $24-$30 Heatgun compared to a
$800-$1900 BGA Rework Station!

 

allcocm1 on 2010-11-10 21:28:44 :

Reflowed the GPU twice on this one before I noticed that someone had managed to
knock a cap off the top of the CPU. Waste of time. This will go back to the
customer who'll probably put it back on FLeBay where I expect it came from
in the first place!

 

DGCNY on 2010-10-18 23:44:08 :

E73 error is also caused by missing capacitors on the CPU. Be sure to check them
as well. Most people aren’t going to notice they are missing.

 

bigart666 on 2010-10-08 05:03:14 :

it is the gpu i had one just messing around stuck 2 q-tips 1 in each fan let it
overheat boom it worked so im off to reflow the gpu

 

mikep3000 on 2010-09-02 04:05:11 :

i had a e74 error and did the heatgun reflow. now i got the e73 error 1021
error. what can i do? any ideas? why i got e74 then e73?

 

wes on 2010-08-10 21:34:43 :

I got this E73/1021 error, I did a DIY adv. hybrid on just the GPU. Found
component video still wouldn't display anything, HDMI & VGA would show
E73 error onscreen. Overheated it with fan on CPU for 8 minutes (felt hot
enough), left it cool for about an hour, tried it and it worked! But only showed
logo and never went to dash (image kept moving tho) and colour + syncing was
off.

Tightened the mobo screws in EVENLY and gently, powered it back on and got green
lights before a crystal clear dashboard!

Then I checked Kernel and it's an exploitable Jasper! :D

Good luck!!

Summary: it's defo GPU related in my opinion!! Also, I found 2 tooth picks
inside this unopened box! :D

 

kip3000 on 2010-08-09 14:37:44 :

Having a hard time with this ec. reflowed gpu, cpu, hana, southbridge...still
nothing but e73. my setup is Presto griddle as preheater with Saike 852d+ hot
air reflow station. I am builind a reflow oven to see if that will help.

 

NickdogV on 2010-06-09 06:21:59 :

I have repaired 4 out of the 7 E73 Units that have been brought to me for repair
by reflowing just the GPU with an Aoyue 968 and an Ownta T-8280 as my preheater.
I have not tried reflowing the Southbridge so I can't be certain if that
works or not. I am pretty sure a heatgun/griddle can get the job done as well.

 

cdrom20 on 2010-06-09 01:57:27 :

This EC is a toufy! I recommend the x clamp fix first and if that isn't
helpful try reflowing the southbridge hana area. And even if that doesn't
work... put back the x clamps and put it together and boom you're screwd!

 

Add a new comment:

Remaining characters:

Anti-spam: Captcha



Copyright Information: Lately it has come to our attention that more and more people stole content from this Error code Database without giving credit, some also restricted access to this information and demanded a payment, we would like to point out that it is perfectly fine to republish content from XE on other sites, however we demand a link back to this error code database and the information must be freely and non commercially available, we appeal to those who feel addressed, add a link and respect the work of others, thank you...

Notice: None of this is official, the methods have often been proven to work but success cannot be guaranteed, you do it on your own risk!
If your console is still covered by the 3 year warranty use it because Microsoft will fix it for free!
A lot of the information you are getting here has been collected in the community, so thanks to everybody who shared his misery!




Back
 
 
 

 
 
 

Xbox Repair Guide

Please select the number of (red) lights that your ring of light shows:

0 red lights
0
 
1 red light
1
 
2 red lights
2
 
3 red lights

4 red lights
4
 


or

Error codes

Go straight to the Error code list/ Database!